Click on the Gorilla link at the top of this page to see other quality products from the Gorilla Glue Company. When areas have completely dried, sand as needed. Clean up while glue is wet: Use a clean, damp cloth to wipe off excess glue. Cure Time (amount of time for glue to reach total bonding strength): 24 hours. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping: The technique and type of clamp to be used is determined by many factors. One fluid ounce will cover approximately 1.6 square feet. Coverage: One gallon of Gorilla Wood Glue will cover about 200 square feet. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping.
Rub together with the other surface to distribute the glue evenly on both surfaces. On hard-to-glue woods, apply the glue on both surfaces. In general, apply a generous amount of glue on one of the surfaces. Also, be careful to avoid burnishing and end snipes. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to use, water-based adhesive, with Gorilla strength.
#GORILLA WOOD GLUE 4OZ FREE#
For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Directions: For best results, it is essential that the wood surfaces are prepared prior to application of glue. This PVA glue is incredibly water resistant and dries a natural color that offers an invisible bond line for your projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to use, water-based adhesive, with the holding power Gorilla is known for. To remove Gorilla Wood Glue from hands, wash with warm soap and water.Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.
#GORILLA WOOD GLUE 4OZ SKIN#
Soak hands and skin in soap and warm water, wash, then rinse.Ĭleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. Wash hands, skin and damp cloths in soap and warm water, then rinse.Ĭlean up when glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from surface, then sand as needed. Make as many passes as needed with the clean area of the cloth to remove all the glue. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.Ĭure Time (amount of time for glue to reach total bonding strength): 24 hoursĬlean up while glue is wet: Use a clean, damp cloth to wipe off excess glue. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.Ĭlamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The technique and type of clamp to be used is determined by many factors: the specific type of joint, type of stock or lumber, moisture content of stock, room temperature, assembly time and surface quality. 1 fluid ounce will cover approximately 1.6 square feet. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. Just how much Gorilla Wood Glue to apply depends on many factors. Also, be careful to avoid burnishing and end snipes.
For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. A PVA glue, offers benefits of an easy-to-use - water-based adhesive for indoor & outdoor use Has holding power Gorilla Glue is know. For best results, it is essential that the wood surfaces are prepared prior to application of glue.
0 kommentar(er)
